What is the right width for electric swing gates?

The opening should match your actual traffic needs, not simply the width of the gap. A single car requires a minimum clear opening of 2.7 metres; two vehicles passing comfortably need at least 5 metres. Most residential driveways in Kent fall between 3 and 4 metres, well suited to a standard double gate split into two equal leaves. For openings wider than 5 metres, your installer will likely recommend a sliding gate as a more structurally sound solution, since very wide swing leaves place considerable stress on the post foundations and motors.

Do electric swing gates require planning permission in Kent?

In most cases, no. Permitted development rights cover gates up to 2 metres in height that open inward and are not adjacent to a classified road. The limit reduces to 1 metre for gates fronting a highway. Listed buildings and conservation area properties require consent regardless of height. Kent has a high concentration of planning designations: the North Downs AONB, the High Weald AONB, extensive Green Belt coverage along the M25 corridor, and conservation areas across every district. Your installer will flag any planning considerations at the site survey and can recommend a pre-application enquiry where there is any doubt.

Vetted Installers in Loose

Electric Swing Gates in Loose

Kent electric swing gates specialists covering Loose. Site survey at no charge, written quotes, no obligation to proceed.

Electric Swing Gates specialists in Loose, verified and active in Kent

Up to three independent quotes, each with a free site survey

Insured, warranted, and commissioned to BS EN 12453 as standard

Highly rated by Kent homeowners

Free Matching Service

Get Matched in Loose

Up to 3 vetted installers will contact you within 24 hours

Minimum 50 Residential Installs

Every Loose installer in our network specialises in gate installation and has a verified project history before receiving a single referral from us.

Site Survey Within the Week

Most installers covering Loose can offer a free site survey slot within 7 days, with evening and Saturday appointments available.

Insured and Warranted

Public liability cover and written warranties on both the gate and the automation are required from every installer before we refer any Loose enquiries.

Matched to Your Gate Type

We connect you with Loose installers who have specific experience with electric swing gates, not a general list of whoever is available.

Electric Swing Gates in Loose: What to Expect

Swing gates are the most widely installed gate type on residential properties in Loose, and the preference is well founded. Paired gates opening as you approach the driveway deliver a combination of visual impact and daily convenience that other formats do not quite match. The technology is mature, the installer population that can execute the work reliably is substantial, and the range of materials and motor configurations gives genuine flexibility across different property types.

The motor decision shapes the entrance aesthetic as much as the gate design. Underground motors sit in a chamber below the post, invisible when the gate is closed, and are the preferred specification on premium Loose properties. Ram-arm motors mount on the face of the gate and post, visible from inside. They are the practical and cost-effective choice on retrofit projects where post foundations do not allow excavation. Your installer will make an honest assessment at the survey based on gate weight and post condition.

How Electric Swing Gates Installation Works in Loose

Submit your Loose enquiry with gate type, opening width, and approximate budget. We match you with up to three swing gate specialists covering your area.

Each installer visits the Loose property, measures the opening, walks the full swing arc to confirm clearance, and checks pillar and foundation condition before recommending motor type.

You receive a written quote covering gate fabrication or supply, post foundations, motor installation, safety photocells, and access control equipment.

Where new gates are fabricated, allow 2 to 5 weeks for manufacture depending on material and design complexity.

On site, post foundations are set or verified, underground motor chambers excavated where specified, and electrical conduit installed before surface reinstatement.

Gate leaves are hung and aligned, motors fitted into chambers or onto post faces, photocells positioned for full arc coverage, and all wiring terminated.

The complete system is programmed and tested to BS EN 12453. Travel limits set, force limits calibrated, all access devices paired, and the manual release demonstrated.

How Much Do Electric Swing Gates Cost in Loose?

Driveway gate prices in Loose vary depending on the gate type, material, and level of automation. Below are typical costs from vetted installers in the Loose area. All prices are in GBP and include full installation.

Gate Type	Price Range	Install Time	What is Included
Electric Swing Gates (Fully Installed) Covers gate fabrication or supply, post foundations, underground or ram-arm motors, two remote handsets, and BS EN 12453 compliant safety sensors. Underground motors and bespoke wrought iron designs sit toward the top of the range. The most widely installed gate type across Kent.	£3,800 to £11,500	2 to 4 days	Gate + motor + posts + remotes

Electric Swing Gates (Fully Installed)£3,800 to £11,500

2 to 4 daysGate + motor + posts + remotes

What's Included in the Price

Free site survey with no obligation to proceed
Bespoke gate design and workshop fabrication
All groundwork, post foundations, and concrete work
Automation motor, control board, remotes, and safety sensors
Intercom, keypad, or proximity reader wiring where specified
Full BS EN 12453 commissioning, testing, and written handover

0% Finance Available

Most Kent installers in our network offer 0% interest finance on gate installations. Spread the cost of your project over 6 to 36 months from as little as £99 per month, with nothing to pay upfront at many providers. Subject to status and approval.

From £99/month

Spread over 6 to 36 months at 0% APR representative

The cost of driveway gates in Loose depends on several factors: the material (wood, steel, aluminium, or wrought iron), whether you want automation, the width of your driveway entrance, and any bespoke design requirements. Prices vary across Kent depending on site conditions and specification, but the installers in our Loose network are competitively priced for the quality of work they deliver. Every installer offers a free site survey so you can get an accurate, itemised quote before making any commitment.

Why Get Electric Swing Gates in Loose Through Us?

Swing gate installers in our Loose network understand the property types, plot sizes, and terrain across this part of Kent.

Underground and ram-arm motor options available with clear guidance on which suits your gate weight and post condition.

BS EN 12453 commissioning completed and documented on every installation before handover.

Written warranties covering gate structure and automation provided separately by every Loose installer in our network.

Electric Swing Gates in Loose: Common Questions

Inward opening is the standard and, in the majority of cases, the only permitted direction. UK highway regulations prohibit gates from opening over a public footpath or road, which rules out outward-opening designs for most Kent residential properties. The exception arises where the driveway slopes steeply downward from the road toward the house, making inward opening mechanically difficult. In those cases, installers typically use articulated hinge systems or higher-torque underground motors to manage the gradient rather than reversing the opening direction. Sloped approaches are common across the North Downs ridge and the Wealden hills.

What Homeowners Are Saying

“We needed gates that would sit comfortably within the North Downs AONB without drawing objections. The installer specified iroko swing gates with underground motors and managed the whole project from design through to commissioning. The result looks as though it has always been there, which is exactly what we wanted.”

Jonathan P.

Sevenoaks · Electric Swing Gates

“Our conservation area property needed a gate that respected the street scene while providing genuine security. The fabricator produced hand-forged ironwork that matched the period railings perfectly and the installer handled the listed building consent paperwork alongside us. Exceptional attention to detail throughout.”

Helen and Mark D.

Canterbury · Metal Driveway Gates

Get Electric Swing Gates Quotes in Loose

Submit your enquiry in under two minutes. We will match you with up to three vetted Loose installers for free site surveys, written quotes, and no obligation at any stage.